product
recalls, safety
alerts & notices
The most up to date product recalls, safety alerts & notices available on
the web. Keep checking back, we will update this page as needed.
All Product Recalls, Safety Alerts & Notices
02/24/26 // Petzl // Safety Alert: Petzl ASTRO and CANYON GUIDE Harnesses
The following is from Petzl:
“User feedback alerted us to premature wear of the screws on the gated ventral attachment point on ASTRO rope access harnesses manufactured before October 2023 (harnesses that were affected by our call for inspection of ASTRO and CANYON GUIDE harnesses in 2023).
Our assessment found that these harnesses may present a non-conformity which cannot be detected by the test requested in our previous call for inspection. This non-conformity, combined with a specific use involving high lateral stress on the attachment point, leads to premature wear of the screws.”
-Petzl
08/1/25 // MSA // User Notice: MSA V-EDGE® Web PFLs
The following is from MSA:
“This User Notice is to alert you to the need for an additional step in customer pre-use checks and examination procedures regarding MSA V-EDGE® Web PFLs (Personal Fall Limiters) that were manufactured between May 2018 up to and including January 2025. Please review the full notice for individual model numbers.
MSA has received an isolated field report that a bolt that connects the PFL ring to the Energy Absorber of the V-EDGE Web PFL separated from the unit, resulting in the unit being non-functional. MSA has not received any reports of injuries associated with this condition. However, we request that you perform the inspection outlined in this notice prior to your next use and include it in your pre-use checks and examination procedures.”
-MSA
04/29/2025 // CMC / Harken // Inspection Notice: CMC CLUTCH™ by HARKEN™
The following is from CMC / Harken:
“CMC and Harken are issuing a Product Inspection Notice for CLUTCH units manufactured November 19, 2024 through April 10, 2025. We have identified one 11 mm CLUTCH unit that has shipped to a customer with a loose rivet pin. As a precautionary measure, we are issuing this Product Inspection Notice for 11 mm and 13 mm CLUTCH units (Product Numbers: 335011-01 & 335013-01) with serial numbers 2024 324 – 001 through 2025 100 – 999.”
-CMC / Harken
03/04/25 // PETZL // Important Voluntary Recall: Swan Easyfit Steel and Stainless Harness
The following is from Petzl:
“Petzl is voluntarily recalling the SWAN EASYFIT STEEL harnesses (references C062AA00 (single) and C062AA01 (5-pack)) and SWAN EASYFIT STAINLESS harnesses (references C062BA00 (single) and C062BA01 (5-pack)) due to a defect in the FAST LT buckle that could lead to a fatal fall. Please immediately stop using the harnesses affected by this recall.”
-Petzl
03/04/25 // PETZL // Recall: Newton, Newton Fast, and Newton Easyfit Harnesses – European Versions
The following is from Petzl:
“Recall of certain batches of the European Version of NEWTON harnesses manufactured in 2022 (references C073AA01 C073AA02), NEWTON FAST (references C073CA01 and C073CA02) and NEWTON EASYFIT (references C073EA00, C073EA01, and C073EA02) due to a nonconforming batch of FAST LT buckles that could lead to a fatal fall. Immediately stop using the harnesses affected by this recall.”
11/06/24 // 3M // “Stop Use and Recall / Replace or Remediate” Notice: Select 3M™ DBI-SALA® Sealed-Blok™ Self-Retracting Lifelines
The following is from 3M:
“As part of 3M’s ongoing commitment to delivering high quality products, we are notifying our customers of the following information related to select 3M™ DBI-SALA® Sealed-Blok™ Self-Retracting Lifelines (SRLs). 3M Personal Safety Division has identified an aging effect that may impact the performance of the 3M™ DBI-SALA® Sealed-Blok™ SRLs produced from January 2022 to October 2024. Additionally, any devices repaired by 3M, or an authorized service center (ASC), during this timeframe may also be affected. Through laboratory testing, 3M has determined that in the event of a fall, these devices may not lock up as designed which could expose the worker to serious injury or death. There have been no reports of injuries associated with this issue. Affected sizes are all variants of the 85 ft (~26M), 130 ft (~40M), and 55 ft (~17M) self-retracting lifelines, see appendix for the full list of models impacted by this stop use notice.“
02/12/24 // MSA // Inspection Notice: MSA Latchways® Guided Type Fall Arrester
The following is from MSA:
“This Inspection notice is to inform you of a one-time inspection procedure regarding the locking pin on MSA ® Guided Type Fall Arresters (GTFAs) that were manufactured between February 16, 2021 and January 30, 2024. Potentially affected models are listed in Table 1 below.
MSA has received a field report of an MSA Latchways GTFA that did not have a locking pin in the nut of the swivel connector between the carabiner and main body of the unit. Without this locking pin in place, there is potential for the connection to come loose during operation.
MSA has not received any reports of injuries associated with this condition. However, we are requesting that you perform the inspection outlined in this notice prior to next use.
-MSA”
11/30/23 // ISC // Safety Notice/Product Recall: ISC UltraLink
The following is from ISC:
“Following on from our inspection notice issued 17 November 2023, our team has been intensively investigating the potential risk and the root cause of the problem. Our investigation identified that the press fixture used to secure the assembly of the SafeLock button moved outside of specification, creating the potential for a faulty press fit of the button, which can lead to the button turning open and coming apart.
Due to the risk of unintentional opening of the device, which could result in a life-threatening situation, we are issuing this notice instructing users to stop using their device, if it falls within the range of serial numbers:
LK100A1.2: 170431 – 177209; or LK101A1.2: 170433 – 176974.
STOP USING ANY OF THE ABOVE ITEMS IMMEDIATELY
AND REMOVE THEM FROM SERVICE
Manufacturing corrective actions have been introduced to repair and ensure that the press fixture remains within specification; and additional procedures have been introduced to ensure that the SafeLock buttons are secured correctly. Validation testing has been successfully completed and production of UltraLinks has resumed, with this new process in place.
REGISTER YOUR DEVICE FOR RECALL
-ISC”
10/30/23 // PETZL // Request for Quarantine and Inspection: Petzl ASTRO BOD FAST, ASTRO SIT FAST and CANYON GUIDE Harnesses
Following the detection of a defect on the metal D gated ventral attachment point of a harness, Petzl is requesting that all customers quarantine and inspect the ASTRO BOD FAST, ASTRO SIT FAST and CANYON GUIDE harnesses.
08/08/23 // MSA // User Safety Inspection Notice: MSA ALTAIR 5X PID
MSA is issuing this User Safety Notice to inform you of a procedural update regarding usage of the Altair 5X PID gas detector.
01/06/23 // 3M // Inspection Notice: Specific 3M™ Protecta ® Construction & Vest Style Harnesses
“3M Fall Protection has identified a limited number of Protecta Harnesses where the harness webbing is not routed through the adjuster. This condition results in the adjuster not being able to be adjusted or does not lock in place after adjustments have been made. The assembly error is believed to affect only a limited number of units and has been corrected.”
– 3M
12/21/22 // ROCK EXOTICA // Product Recall / Hazard Notice: Omni 1.1″ Pulley Variants, 20050xxx through 22304xxx
“The button assembly on a limited number of 1.1” Omni Swivel Pulleys and associated variants may not be secure. If the button comes out the side plate can open, allowing the rope to fall out which can result in serious injury or death. It was discovered that a small number of pulleys manufactured from February 2020 through October 2022 may not have had adequate thread locker or sealant, allowing the set screw to back out. Under normal circumstances, either the thread lock or sealant is adequate to secure the button and prevent this issue.
Rock Exotica is issuing a recall for Omni Block 1.1” style pulleys, manufactured from February 2020 through October 2022. These pulleys must be returned to us for inspection / repair.”
– Rock Exotica
11/02/22 // DMM // Product Recall / Hazard Notice: DMM Compact Swivel Units
“We have been made aware of a near-miss incident involving the failure of a DMM Director connector (A647BS) that parted at the swivel assembly. The user was unhurt. Our investigation has identified a product fault that, under certain circumstances, may allow the swivel assembly to unscrew and subsequently part.”
– DMM
06/09/22 // 3M // Stop Use / Recall: Select 3M™ DBI-SALA® ShockWave™2 Arc Flash Shock Absorbing Lanyards
“As part of 3M Fall Protection’s ongoing commitment to delivering high quality safety equipment, we are notifying our customers of the following information related to specific 3M™ DBI-SALA® ShockWave™2 Arc Flash Shock Absorbing Lanyards. During an internal review, 3M Fall Protection has identified a potential manufacturing issue with a limited number of devices. This manufacturing issue could result in the lanyard not performing properly in the event of a fall, which could result in severe injury or death. Please reference Appendix A for products that are impacted by this notice. There have been no reports of injuries, accidents, or complaints associated with this issue.”
– 3M Fall Protection
05/02/22 // 3M // Product Advisory: Select 3M™ DBI-SALA® ExoFit™ XP Arc Flash Harnesses
“As part of 3M Fall Protection’s continued commitment to producing high quality safety and personal protective equipment, we conduct periodic testing of our products. The Arc Flash Standard (ASTM F887) requires that all arc flash rated harnesses be subjected to an Arc Flash followed by a successful dynamic drop test. It should be noted that there is variability in Arc Flash testing of webbing-based products that stems from several contributing factors including positioning, webbing gap to the test torso, environmental elements, arc path, input energy and other possible sources.”
– 3M Fall Protection
05/02/22 // 3M // Product Advisory: Select 3M™ DBI-SALA® Delta™ and 3M™ Protecta® Harnesses
“As part of 3M Fall Protection’s ongoing commitment to delivering high quality safety equipment, we are notifying our customers of the following information related to specific 3M™ DBI-SALA® Delta™ and 3M™ Protecta® Harnesses. During internal testing, it was discovered that some models of these harnesses did not consistently meet the required performance of ANSI Z359.11-14 clause 4.3.4 headfirst dorsal dynamic drop at the required 3600 lbs. (16 kN) impact force.”
– 3M Fall Protection
02/03/22 // 3M // Inspection Notice: Select 3M™ Protecta Self Retracting Lifelines
“3M™ Fall Protection has identified a potential manufacturing issue with a limited number of 3M™ Protecta® Self-Retracting Lifelines (SRL) with galvanized or stainless-steel lifelines produced in September 2021. There have been no reports of injuries or accidents associated with this issue. This manufacturing issue could result in the SRL not engaging properly but can be easily detected through the pre-use inspection as specified in the Instruction for Use (IFU) document. Affected part numbers can be found in Appendix 1.”
– 3M Fall Protection
12/08/21 // CMC // Product Inspection Notice: CMC Clutch™ by Harken Industrial™
“CMC and Harken Industrial have identified that a very limited number of 11 mm and 13 mm CLUTCH units may have shipped to customers without the stainless steel Friction Shoe installed. While internal testing shows the missing Friction Shoe does not present an immediate safety concern, there may be impacts to long-term device durability and its performance in extreme circumstances.”
– CMC
11/08/21 // CLIMBING TECHNOLOGY // Product Inspection Notice: Rollnlock Pulley / Rope Clamp
“Climbing Technology has voluntarily issued a request for inspection of the ROLLNLOCK pulley/rope clamp (Ref. No. 2D652) by the user. One of our customers has detected a defect in the functioning of the “sheave position lever” (F). This defect can lead to an accidental locking of the sheave position lever on its pin (H) on the plate. As a result of this defect, when using the device in “hauling pulley” mode, the lever may inadvertently engage the pin suddenly, disabling the locking function and releasing the load or person. “
– Climbing Technology
10/28/21 // 3M // Product Advisory: 3M™ DBI-SALA® Delta™, ExoFit™, ExoFit™ Plus & ExoFit™ XP Cross Over Style Harnesses ANSI & OSHA Versions
“This is not a recall, the 3M™ DBI-SALA® Delta™, ExoFit™, ExoFit™ Plus & ExoFit™ XP Cross Over Style Harnesses remain safe for use. As part of 3M Fall Protection’s ongoing commitment to delivering high quality safety equipment, we are notifying our customers of the following information related to the 3M™ DBI-SALA® Delta™, ExoFit™, ExoFit™ Plus & ExoFit™ XP Cross Over Style Harnesses portfolios. During internal testing of certain 3M™ DBI-SALA® Delta™, ExoFit™, ExoFit™ Plus & ExoFit™ XP Cross Over Style Harness models, we found that a percentage of tested units did not meet the ANSI Z359.11, Section 3.2.2.3.1 dynamic requirement on the front (sternal) D-ring. This test and the resulting forces are not representative of what would be seen in real world application (i.e. when attached to a vertical cable sleeve with an energy absorbing device).”
– 3M Fall Protection
10/27/21 // 3M // Stop Use & Inspection Notice: Specific 3M™ DBI-SALA® Nano-Lok™ Self Retracting Lifeline with Anchor Hook
“As part of 3M Fall Protection’s ongoing commitment to delivering high quality safety equipment, we are notifying our customers of the following information related to specific versions of the 3M™ DBI-SALA® Nano-Lok™ Self Retracting Lifeline with Anchor Hook. 3M Fall Protection has identified a very low potential for the DBI-SALA® Nano-Lok™ Self Retracting Lifeline with Anchor Hook to be assembled with a unformed top swivel eye rivet. An improperly formed rivet may become displaced from the top swivel eye. An unformed rivet may result in the SRL becoming detached from the anchor hook, which could result in severe injury or death.”
– 3M Fall Protection
09/23/21 // 3M // Stop Use & Recall: Specific 3M™ DBI-SALA® Delta™ Arc Flash Web Loop Rescue Safety Harness 3M™ DBI-SALA® ExoFit™ XP Arc Flash Rescue Web Loop Harness ANSI and CSA Versions
“As part of 3M Fall Protection’s continued commitment to producing high quality safety and personal protective equipment, we conduct periodic testing of our products. Recent testing of specific DBI-SALA® Delta™ and ExoFit™ XP Arc Flash harnesses have returned negative test results on some units. The Arc Flash Standard (ASTM F887) requires that all arc flash rated harnesses be subjected to an Arc Flash followed by a successful dynamic drop test.”
– 3M Fall Protection
08/31/21 // PETZL // Safety Information: Cases of Slippage with Zigzag / Zigzag Plus / Zillon
“We have received reports of users experiencing rope slippage while using the ZIGZAG, ZIGZAG PLUS and ZILLON. Following these reports, we have identified two defects causing the slippage. We therefore ask you to do a manual inspection and a function test of your product, to detect any possible slippage. In case your product slips, we are providing details on our after-sales returns service.”
– Petzl
07/26/21 // 3M // Product Advisory: 3M™ Protecta® PRO-Stop™ Single Leg & PRO™ Pack Twin Leg Shock Absorbing Lanyards
“This is not a recall, the 3M™ PROTECTA® PRO-Stop™ Single Leg & Pro™ Pack Twin Leg Shock Absorbing Lanyards remain safe for use. In all tests, these lanyards continued to meet all dynamic requirements of OSHA 1926.502 (d)(16) proving that these lanyards would arrest a fall. The Pro™ Pack Twin Leg Shock Absorbing Lanyard portfolios are also certified to ANSI Z359.13 and meet the dynamic requirements of this standard. We are not aware of any accidents or injuries related to the condition described above. We have not received any customer complaints regarding this but have identified it through an internal review.”
-3M™
03/19/21 // MILLER BY HONEYWELL // Immediate Mandatory Inspection Notice: Miller MightEvac and MightyLite Self-Retracting Lifeline
“At Honeywell, our mission is to continue to provide innovative personal protective equipment that helps our customers maintain workforce safety. You have been identified as a customer that has purchased certain Miller MightEvac and MightyLite Self-Retracting Lifelines (SRLs) products that were returned for repair work by Honeywell between September 1, 2019 and March 5, 2021 (the “Repair Period”). Honeywell has identified a potential issue with reworked brake components that may cause the products to not operate to specification.”
– Honeywell Industrial Safety
03/03/21 // PROTECTTION // Security Alert: Wind Escapettor Rescue Descender and Parttner Complement
We have detected that when the following conditions are met at the same time:
1. There is an overload in the equipment.
2. An excessively strong actuation of the lever is carried out.
The Wind Escapettor rescue descender can damage the rope, even severing it due to the aggressiveness of the anti-panic cam tooth of some equipment. This problem has been identified in the devices with the serial number starting by 20.05 and 20.02 These circumstances of unforeseen use, in which the rope can be damaged, are exceptional and do not correspond to the usual use of the equipment, nor to those contemplated in the tests carried out for its approval.
01/04/21 // MSA // User Safety Notice: Latchways Standard Self-Retracting Lifeline
MSA is issuing this User Safety Notice to inform you that MSA has received field reports of a limited number of Latchways Standard Self-Retracting Lifelines (SRL) in which some internal bolts came loose. MSA has not received any reports of injuries associated with this condition. However, we are requesting that you perform the actions outlined in this notice. Over time, the loose bolts will be identifiable by the user as extraction of the cable from the SRL housing will no longer be possible. However, MSA’s investigation has determined that this may be preceded by a window of time in which a fall may not be arrested.
08/28/20 // 3M // Inspection Notice: 3M™ Protecta® Rebel Self Retracting Lifelines (ANSI Versions)
“3M™ Fall Protection has identified a potential manufacturing issue with a limited number of 3M™ Protecta® Rebel Self-Retracting Lifelines (with galvanized or stainless-steel lifelines) produced between October 14, 2019 and February 25, 2020. There have been no reports of injuries or accidents associated with this issue. This manufacturing issue could result in the SRL not engaging properly but can be easily detected through the pre-use inspection as specified in the Protecta® Rebel Instruction for Use (IFU) document.”
-3M™
08/06/20 // 3M // Stop Use & Product Recall: 3M™ DBI-SALA Self-Rescue Descent System
“Given this recent information, 3M Fall Protection is issuing a “Stop Use and Recall” of all 3 models of the 3M™ DBI-SALA® Self-Rescue Descent Systems including P/N 3320030; 3320031 & 3320037. We have completed a review of returned training units from the field and have concluded that this cracking condition is also a result of embrittlement overtime of the plastic spool used to hold the lifeline rope. This embrittlement could inhibit the ability of the Self-Rescue Descent System to fully descend an end-user in the event of a fall. This spool is internal to the Self-Rescue Descent System and unlike the training, models cannot be inspected. Please note we are not aware of any accidents or injuries related to this condition.”
-3M™
07/21/20 // PETZL // Inspection Request: Kernmantle Ropes
“One of our clients found 2 critical defects on his Petzl low-stretch kernmantle ropes. To date, no other client has reported similar defects to us, and no accident or injury is known. Please read the information below and, if necessary, inspect your ropes.”
-Petzl
05/13/20 // 3M // Stop Use: 3M™ Fall Protection Specific DBI-SALA® Delta™ & Exofit XP™ Arc Flash Harnesses
“As part of 3M Fall Protections continued commitment to producing high quality safety and personal protective equipment, we conduct periodic testing of our products. Recent testing of specific DBI-SALA® Delta™ & Exofit XP™ Arc Flash harnesses have returned negative test results on some units. The Arc Flash Standard (ASTM F887) requires that all arc flash rated harnesses be subjected to an Arc Flash followed by a successful dynamic drop test. It should be noted that there is variability in Arc Flash testing of webbing based products. Although not fully understood, it can stem from several contributing factors including positioning, webbing gap to the test torso, environmental elements, arc path, input energy and other possible sources.”
-3M™
01/07/20 // 3M // Product Advisory: 3M™ DBI-SALA® EZ-Stop™ Shock Absorbing Lanyards (ANSI Versions Only)
“As part of 3M Fall Protection’s on-going commitment to delivering high quality safety equipment, we are notifying our customers of the following information related to the 3M™ DBI-SALA® EZ-Stop™ Shock Absorbing Lanyard portfolio.
With respect to the voluntary ANSI/ASSE Z359.13-2013 standard, recent 3M testing produced results marginally (~2-4%) above the maximum requirement for testing in ambient, dry conditions.1 We believe this is the result of a raw material issue, which we are currently investigating (with in-scope product shipments currently on hold pending completion of that work). Product shipments will resume as soon as products are requalified to meet applicable requirements.”
-3M™
10/31/19 // MSA // Inspection Notice: MSA Workman® Mini & V-Edge™ Web 8ft/2.4m PFLs
“MSA is issuing this Inspection Notice to inform you that MSA has received a limited number of field reports in which the lifeline in a WORKMAN MINI PFL did not retract after being fully extended. MSA has not received any reports of injuries associated with this condition. However, we are requesting that you perform the inspection outlined in this notice.”
-MSA
08/23/19 // MILLER BY HONEYWELL // Mandatory Stop Use Notice: Miller MightEvac and MightyLite Self-Retracting Lifelines Safety Notice
“At Honeywell, our mission is to be the global leader in personal protective equipment with innovative solutions that protect and save lives. In line with our commitment to our mission statement, we are writing to inform you of potentially non-conforming brake components in certain models of Miller MightEvac and MightyLite Self-Retracting Lifelines (SRLs) ranges manufactured within a specific timeframe. While there have been NO reported incidents due to this nonconformity, continued use of the product could result in serious injury or death.
We have already determined a solution for the potential non-conforming brake components for affected models of Miller MightEvac and MightyLite Self-Retracting Lifelines (SRLs), which will require replacement of the brake component at our repair center. We apologize for the inconvenience this may cause and potential business disruption. We urge you to immediately discontinue use of affected units to avoid safety risks.”
– Honeywell Industrial Safety
08/05/19 // 3M // Stop Use & Recall Notice: Update and Solution 3M™ DBI-SALA® Twin-Leg Nano-Lok™ edge Self-Retracting Lifelines (ANSI Versions Only)
“3M Fall Protection is pleased to announce it has resolved the partial deployment of the energy absorber that led to the immediate stop use and recall of the 3M™ DBI-SALA® Twin-Leg Nano-Lok™ edge SRL issued in North America on July 25, 2019. A robust solution has been identified, tested and certified to the ANSI standard Z359.14. With this solution, the energy absorber of these units will deploy properly under all circumstances of use for which these products are intended. The affected units can now be repaired and safely returned to service.”
– 3M Fall Protection
07/25/19 // 3M // Stop Use & Product Recall: 3M™ DBI-SALA® Nano-Lok™ edge and Wrap Back Twin-Leg Self Retracting Lifelines
“3M Fall Protection announces an immediate stop use and product recall of the 3M™ DBI-SALA® Twin-Leg Nano-Lok™ edge and the Twin-Leg Nano-Lok™ Wrap Back Self-Retracting Lifeline. These Twin-Leg Nano-Loks are used as part of a personal fall protection system that connects two self-retracting lifelines/devices (SRLs/SRDs) directly under the dorsal D-ring of a worker’s harness. The Twin-Leg Nano-Lok edge is intended to be anchored at foot-level, is designed for sharp and/or leading edge applications and incorporates an energy absorber. The Twin-Leg Nano-Lok Wrap Back is intended for wrapping around an anchor and incorporates a similar energy absorber. 3M has determined that in a fall and under certain conditions, the energy absorber of these devices may not properly deploy which could expose the worker to serious injury or death. There have been no reports of accidents or injuries associated with this issue, these products must be removed from service immediately.
To address this situation, in the interests of worker safety, 3M is launching a global stop use of the Twin-Leg Nano-Lok edge and Twin-Leg Nano-Lok Wrap Back SRL devices. 3M is recalling all these devices to be repaired or replaced as soon as a solution is identified, tested and certified. Alternatively, end-users may elect to receive cash for their returned devices as described below. This stop use/recall affects all models of the Twin-Leg Nano-Lok edge and Twin-Leg Wrap Back SRLs since first introduced in 2013. This stop use/recall does not affect the single-leg versions of these models. As of the date of this notice, no 3M twin-leg SRL product is approved for use over sharp or abrasive edges.“
– 3M Fall Protection
07/25/19 // 3M // Stop Use & Product Recall: IMMEDIATE ACTION REQUIRED 3M™ Protecta® Cobra Rope Grab AC202D
“3M Fall Protection has determined that the 3M™ PROTECTA® Cobra Mobile/Manual Rope Grab AC202D is incorrectly stamped for use with 1/2 to 3/4 inch diameter rope on the exterior body of the unit. This Cobra Rope Grab is certified for use ONLY with 5/8 inch diameter polyester or polypropylene rope. All marketing information and the Instructions for Use (IFU) for this rope grab correctly identify the size of rope to be used as 5/8 inch polyester/polypropylene rope.
In the event of a fall from height, a Cobra Rope Grab used with 1/2 inch diameter rope may not arrest the fall and could result in serious injury or death to the worker. To remedy this situation, 3M is launching a Stop Use & Product Recall to replace all AC202D and related Cobra Rope Grabs that are stamped 1/2″—3/4″ Dia.”
– 3M Fall Protection
04/16/19 // 3M // Inspection Notice: 3M™ DBI-SALA® ExoFit NEX™ Harnesses
“3M Fall Protection has learned of the possibility of a manufacturing defect in a dorsal d-ring utilized in ExoFit NEX™ harnesses manufactured between January 2016 and December 2018. Although there have been no reported incidents involving this condition, a dorsal d-ring with this defect will not support the load in a fall arrest event which could result in serious injury or death. Harnesses manufactured only within this date range require immediate inspection for lot number 09P1 stamped into a dorsal d-ring. We believe that only one harness was manufactured with a defective D-ring, but we urge inspection of all potentially affected harnesses out of an abundance of caution in the interests of worker safety.
To address the situation, 3M Fall Protection is launching a global Inspection Notice. As set out in the attached Notice, all ExoFit NEX™ harnesses manufactured between January 2016 and December 2018 require inspection prior to use.”
-3M Fall Protection
02/12/19 // 3M // Product Advisory: 3M™ DBI-SALA® Self-Rescue
“3M Fall Protection has identified a manufacturing issue within a limited number of 3M™ DBISALA® Self-Rescue devices manufactured prior to December 2018. There have been no reports of injuries or accidents associated with this issue. The fall-arrest performance of the Self Rescue is not affected by this issue but it may impact the self-rescue function of the unit. The manufacturing issue can be visually inspected and is easily identified through a pre-use inspection.
To address the situation, 3M Fall Protection is launching a global Inspection Notice. As set out in the attached Notice, the impacted model #s 3320030 and 3320031 require inspection prior to use, and users are provided several options including free inspection and/or replacement at [email protected].”
– 3M Fall Protection
01/14/19 // 3M // Product Advisory: D-Ring Extenders in Leading Edge Applications
“3M Fall Protection has received a series of inquiries regarding the use of dorsal D-ring extenders with Leading Edge SRL’s in environments where sharp edges are present. Examples of 3M dorsal D-ring extenders are shown below, but the concern applies to all dorsal D-ring extenders, regardless of the supplier/manufacturer.”
– 3M Fall Protection
11/06/18 // 3M // Quality Alert: 3M™ DBI-SALA® Exofit Harnesses
“3M Fall Protection has received reports that the aluminum reinforcement plate used in the seat sling on certain DBI-SALA ExoFit™, ExoFit XP™ (inc. Arc Flash), and ExoFit NEX™ (inc. Arc Flash) harnesses can become dislodged from the webbing. In a few instances, the aluminum seat plate has separated from the harness and fallen to the ground, creating a potential dropped object hazard. There have been no reports of injuries or accidents associated with this condition. The performance of the harnesses is unaffected by this issue—they will perform properly in all respects, including as body support for a personal fall arrest system in the event of a fall, even without the added comfort offered by the seat sling.”
– 3M Fall Protection
09/12/18 // 3M // Stop Use & Recall Notice: 3M™ DBI-SALA® 16 Foot Talon™ Self Retracting Lifeline
“3M Fall Protection is issuing the attached Stop Use and Recall Notice regarding the 3M™ DBI-SALA® 16 Ft. Talon™ Self Retracting Life Line. We have detected a small quantity of DBI-SALA 16 Ft. Talon™ Self Retracting Lifelines that are defective due to an assembly error. There have been no reports of fall-related injuries associated with this condition. However, this assembly error would result in the unit not arresting a fall, which could result in serious injury or death. Your immediate action is required.”
– 3M Fall Protection
07/11/18 // MSA // Safety Advisory: MSA Green Colored V-Gard® Protective Caps
“MSA is issuing this Safety Advisory to inform you that MSA has received field reports that some green colored MSA V-Gard Protective Caps are cracking. The cracking occurs at the top of the cap, and is not caused by an impact to the cap. MSA has confirmed that the cause of the cracking is limited to green colored, medium size MSA V-Gard Protective Caps and that corrections have been made to prevent recurrence.”
– MSA
04/19/18 // MILLER BY HONEYWELL // Safety Notice: Voluntary Product Recall of Certain Lots of Fibre Metal E2 Cap & North Peak A79
“The safety of our products is our top concern at Honeywell. We have recently learned of a quality issue affecting certain lot numbers of our Fibre Metal E2 Cap and North Peak A79 hard hats that may render them unable to provide the impact protection for which they were designed and certified. The affected hats can be identified by manufacture date and lot, and are set forth on the attached documents below.”
– Honeywell
01/29/18 // MSA // Safety Notice: Stop Use MSA Gravity® Welder Harness
“Upon investigation of the field report, MSA determined that the leg strap and chest strap used in select MSA Gravity Welder Harnesses are incompatible. Although the harness can be donned, in the event of a fall, the shoulder straps may extend and affect the protection offered by the harness.”
– MSA
10/11/17 // CMC RESCUE // Product Safety Notice: CMC Rescue MPD™ 13 MM Model (Red), Part# 333000
“CMC Rescue has received a report of a single MPD™ (13 MM model) that was assembled with an 11 MM model front plate (see photo below). This would provide additional travel of the internal moving brake, potentially allowing greater gripping force on the rope than would be optimal in some applications…”
– CMC Rescue
05/17/17 // 3M/CAPITAL SAFETY // Stop Use Notice: Free Standing Counterweight Anchor Using an Evolution Leap Post
“3M Fall Protection (formerly Capital Safety) has received field reports of broken end-posts (also known as Lead Energy Absorbing Posts, or “LEAP posts”) used in roof-mounted EvolutionTM Horizontal Lifeline Systems. 3M has launched a global Stop Use – Field Service Action to address this situation. The same Evolution end-posts are also used in Free Standing Counterweight Anchor systems. There have been no reports of fall-related injuries associated with this condition.”
– 3M/Capital Safety
03/29/17 // CMC RESCUE // Inspection Notice: CMC Rescue MPD
“CMC Rescue has received a very limited number of reports of one or more of the MPD cover plate cap screws (see photo below) found to be loose. CMC Rescue has determined that this condition does not present a safety hazard to users. Per the supplied User Instruction Card, and as with all life safety equipment, we recommend users inspect the MPD before and after each use. If during visual inspection any of the fasteners are found to be loose, contact CMC Rescue to return the unit for service.”
– CMC Rescue
10/12/16 // CAPITAL SAFETY // Recall Notice: DBI-SALA® Zorbit™ Energy Absorber (Note: Recall limited to lot #2101506 through #2464624 only)
“The ZorbitTM Energy Absorber is used with horizontal lifeline systems to limit fall arrest forces on the worker in the event of a fall. 3M Fall Protection (formerly Capital Safety) has identified a production issue with its Zorbit Energy Absorbers that creates a risk of serious injury or death for a user in the event of a fall from height. Although there have been no reported accidents or injuries associated with this issue, 3M Fall Protection is voluntarily recalling a limited lot range of this product and will replace affected energy absorbers free of charge.”
– Capital Safety
08/30/16 // CAPITAL SAFETY // IMMEDIATE ACTION REQUIRED Product Stop Use & Recall / Replacement Notice: Lad-Saf™ Sleeve
“Capital Safety/3M recently reviewed the performance of the original Lad-Saf sleeve in the field, including a limited number of incidents involving a serious injury or death in the United States while using the sleeve. Although our review did not reveal product hazard or risk scenarios that would arise in the ordinary and proper use of the product, it did reveal potential misuse scenarios that could result in serious injury or death. The potential misuse scenarios include interference with the braking mechanism (such as entanglement with cords, lanyards, clothing or other materials, or grasping the sleeve prior to or during a fall), or result from the user attaching the sleeve upside down (user inversion). No safety regulator has made a finding that the design of the original Lad-Saf sleeve is defective.”
– Capital Safety
04/18/16 // PETZL // Updated Information: ASAP Lock
“On March 30, 2016, during routine equipment inspections, one customer detected cracks on the stainless steel arms on three ASAP LOCK units. In light of this information, a complete inspection of Petzl ASAP LOCK inventory was conducted and no cracked ASAP LOCK arms were found. Mechanical tests conducted by Petzl on the ASAP LOCK with intentionally cut arms showed that a cracked arm presents no additional risk to the user.”
– Petzl
04/18/16 // CAPITAL SAFETY // Product Retrofit Notice: Advance Adjustable Offset Davit System (USA Version)
“Capital Safety/3M recently reviewed the performance of the original Lad-Saf sleeve in the field, including a limited number of incidents involving a serious injury or death in the United States while using the sleeve. Although our review did not reveal product hazard or risk scenarios that would arise in the ordinary and proper use of the product, it did reveal potential misuse scenarios that could result in serious injury or death. The potential misuse scenarios include interference with the braking mechanism (such as entanglement with cords, lanyards, clothing or other materials, or grasping the sleeve prior to or during a fall), or result from the user attaching the sleeve upside down (user inversion). No safety regulator has made a finding that the design of the original Lad-Saf sleeve is defective.”
– Capital Safety
02/22/16 // CAPITAL SAFETY // Product Retrofit Notice: UniRail / RoofSafe Carriage
“Capital Safety is issuing a Product Retrofit Notice regarding the UniRail / RoofSafe carriages manufactured before February 2015. Capital Safety has received a limited number of reports of fractured circlips (the locking screw retaining clips) which can allow the locking screw to unscrew and separate from the carriage body. If the locking screw separates from the carriage body, it is possible for the shackle retaining pin to slide out of the carriage body and release the tie-off shackle.”
– Capital Safety
02/12/16 // AUSTRIALPIN // Courtesy Safety Notice: AustriAlpin COBRA® Buckles
“AustriAlpin released a safety notice on their COBRA buckles (1 out of 2 million) may exist parts where the rivets have not been press fixed.”
– AustriAlpin
09/14/15 // DMM // Product Recall Notice: Select Carabiner Internal Coil Springs
“In a small percentage of carabiners the interaction between the internal coil spring (which gives the gate its closing action) and the gate pusher (the component that holds the spring against the carabiner body) may cause the gate pusher to displace, potentially preventing the gate from closing or the mechanism from locking completely..”
– DMM
03/12/15 // CAPITAL SAFETY // Inspection Notice: Select Carabiner Internal Coil Springs
“Capital Safety has learned of broken screw heads found in a limited number of Protecta brand Rebel Self Retracting Lifelines (SRLs). The units affected by this notice are the black, extruded aluminum housing versions of the Rebel, manufactured between 1 April 2014 and 30 November 2014.”
– Capital Safety
12/19/14 // CAPITAL SAFETY // Product Safety Notice: Lad-Saf Ladder Safety System
Capital Safety has issued a Product Safety Notice to the Tower Industry regarding the Lad-Saf Ladder Safety System.
The affected systems are:
- systems using 3/8 inch 7×19 wire rope galvanized cable
- purchased from Capital Safety between September 1, 2013, and May 13, 2014
Lad-SafProductSafetyNotice19Sept2014
– Capital Safety
04/02/14 // PETZL // Information: Using Petzl Croll L B16 & B16AAA in Corrosive Environments
“As explained in our previous communiqué posted on the Petzl website on March 17, 2014, two different customers have informed us of recent failures of the rivet head on two Petzl CROLL L rope clamps; neither failure led to an accident. These two CROLL L rope clamps were used on offshore platforms in the North Sea. There was no sign of specific wear or damage on either CROLL L prior to the failures.”
– Petzl
02/17/14 // MSA // Inspection Advisory: Yoke Snaphooks
“Yoke Industrial Corporation, the manufacturer of snaphooks used on many fall protection products industry wide, including MSA’s, recently notified MSA of an issue involving the potential for missing or improperly installed rivets on Yoke snaphooks..”
– MSA
01/24/14 // GUARDIAN FALL PROTECTION // Product Inspection Notice: Rebar Hook Failure
“The failure involved the detachment of the u-block from the hook body. The the failure point has been sighted as the threaded bolt/nut.”
– Guardian Fall Protection
02/11/13 // GENIE // Recall Notice: Genie Z-135/70 Boom Lifts
“Genie has become aware of secondary boom angle sensor calibrations performed in the field in which the machine’s service manual may not have been followed creating an improperly calibrated machine. An improperly calibrated machine can lead to machine instability resulting in a machine tip over.”
– Genie
02/11/13 // CAPITAL SAFETY // Safety Recall Notice: DBI-SALA Sayfglida Horizontal Lifeline System (“Sayfglida System”)
“Capital Safety is undertaking a voluntary recall of the sleeve (or shuttle) component of the DBI-SALA Sayfglida Horizontal Lifeline System (“Sayfglida System”). The Sayfglida System is permanently installed as a means of anchoring a fall protection system and consists of a Sayflink Sleeve, a wire cable, and by-passable intermediate brackets. The brackets are designed so that the system may be installed above the user, level with the user, or at walking surface level.”
– Capital Safety
02/01/13 // FALL TECH // Product Inspection Advisory Notice: FallTech Lanyards, Rebar Chain Assemblies, Harness / Lanyard Combos, and Roofer’s Kits
“Please be advised that all hooks on all FallTech Lanyards, Rebar Chain Assemblies, Harness/Lanyard Combos and Roofer’s Kits with manufacturing dates of 01/01/2012 through 01/25/2013 should be inspected immediately in accordance with this notice.”
– FallTech
09/07/12 // MILLER BY HONEYWELL // Notice: Miller Duraflex Harness D-ring
“In response to an unauthorized “safety alert” regarding Miller by Honeywell harnesses, Honeywell Safety Products issued this notice to ensure customers that they have conducted a thorough internal investigation to determine the root cause.”
– Miller by Honeywell
06/29/12 // 3M // Product Recall / Stop Use Notice: 3M Series Self Retracting Lanyards – The THOR Family of Self-Retracting Lanyards Units Manufactured by IKAR from November 01, 2011 to June 25, 2012 (M-, RLD- and 205G- Series)
“3M was recently informed by IKAR GmbH, that their supplier of the brake pad material used in the THOR family of 3M Self-Retracting Lanyards had experienced a process quality issue in the manufacture of the brake pads that could potentially affect the performance of those units.”
– 3M
06/26/12 // GUARDIAN FALL PROTECTION // Inspection Notification: All Guardian Fall Protection (GFP) Products Featuring a Specific SWIVEL SNAPHOOK Shipped From GFP After 08/26/2011
“Inspection notice for GFP products featuring a possible unsafe condition due to a supplier defect in a specific style of swivel snaphook supplied to Guardian between 8/26/2011 and 6/25/2012.”
– Guardian Fall Protection
06/08/12 // PETZL // Announcement: 8003 (C05N) Full Body Harness
“There have been several incidents involving the 8003 (C05N) full body harness. These incidents, all of which occurred during use within the adventure park environment, involve the leg loops of the harness becoming loosened and/or unbuckled during use.”
– Petzl
02/24/12 // PENSAFE / CAPITAL SAFETY // Recall Notice: 3730 Anchorage Connector With A Manufacturing Code 07B
“Capital Safety parts affected by the PenSafe recall, reissued February 7, 2012, include the following: AN112A anchorage connector and Vacuum Anchor models; 2200104, 2200106, 2200047, 2200046, 2200045, 2200037, 2200036.”
– Pensafe/Capital Safety
02/20/12 // PETZL // Notice: All NEWTON C73*** Full Body Fall Arrest Harnesses With A Series Number Equal To Or Less Than 11365***
“Special request to control the sternal attachment point. Improperly positioned safety stitching was found on one of the loops of the sternal attachment point.”
– Petzl
02/14/12 // FALLTECH // Product Stop Use, Inspection & Replace Notice: IMMEDIATE ACTION REQUIRED All FallTech Full Body Harnesses Featuring Quick-Connect (Bayonet Style) Buckles
“It was discovered that the male and female halves of the buckle were improperly paired, which may result in disengagement or unfastening of the buckle while in use.”
– FallTech
02/13/12 // MIO MECHANICAL CORP. // URGENT Recall: MIO Rope Grabs Model RG-1200 (Blue Pin and Roller, for Use on 1/2″ Dia. Rope) Sold During Nov. 1, 2011 to February 10, 2012
“Due to an error during the manufacture of the rope grabs with SN#s 1212, 11112 and 11122 will not work and fail in case of an emergency.”
– Mio Mechanical Corp.
02/07/12 // PENSAFE // Recall Notice: 3730 Anchorage Connector with a Manufacturing Code 07B
“Connectors may be subject to embrittlement that may cause the threads of the stem to fracture. PenSafe has issued a 2nd Release of its Recall Notice, dated February 7, 2012, reminding its customers of the ongoing recall.”
– Pensafe
01/20/12 // CAPITAL SAFETY // Revised Recall Notice: Protecta Shock Absorbing Twin-Leg Lanyards
“The identified reason for the inadvertent disconnection is the combination of a particular style locking snaphook together with twin elastic lanyard legs attached directly to the eye of the snaphook.”
– Capital Safety
01/10/12 // PETZL // Notice: Petzl Shunt
“Findings of indicative tests demonstrate that releasing a towing cord while towing a Petzl Shunt as a back-up device is not consistently effective.”
– Petzl
11/11/11 // CAPITAL SAFETY // Recall Notice: Y-Shaped Protecta Shock Absorbing Lanyards
“A inadvertent disconnection was reported during use of the locking snaphook used in a series of Capital Safety’s “Y-shaped” Protecta lanyards (part number 9502573).”
– Capital Safety
10/26/11 // PENSAFE // Recall Notice: 3730 Anchorage Connector
“Connectors may be subject to embrittlement that may cause the threads of the stem to fracture.”
– Pensafe
09/23/11 // ELK RIVER // Notice: TX12 Series of Energy Absorbing Lanyards
“Elk River has discovered a problem with the manufacture of the TX12 Series of Energy Absorbing Lanyards.”
– Elk River
09/18/11 // 3M // Product Recall / Stop Use Notice: 3M™ G-7 and GW-11 Series Retractable Lanyard Models: GW-7, GW-11, GW-7-0241A, GW-7-0241H, GW-11-0241A, GW-11-0241H, GW-11NS, DLGW-7, DLGW-7-0241A and DLGW-11-0241A
“3M has identified a limited number of units that don’t properly achieve lock up during user inspection. Users are asked to return units for service immediately.”
– 3M
08/29/11 // CMC RESCUE // Product Safety Notice: Escape Artist System (certified to NFPA 1983), Survivor Escape Artist System, or FR Escape Tether with a 7-mm Oval Screw Link That Attaches the Tether to the Escape Artist
“The handle of the Escape Artist may become temporarily caught in the oval screw link. To eliminate risk of this as a safety concern, CMC is offering replacement tethers with a different screw link free of charge to those who have purchased systems or tethers. For purchasers of certified systems, the new assembly retains the system certification to NFPA 1983 when assembled in accordance with the instructions provided with the replacement tether.”
– CMC Rescue
06/20/11 // PETZL // Recall: All GRIGRI 2’s (D14 2O, D14 2G, D14 2B) with the First Five Digits of the Serial Number Between 10326 and 11136
“Petzl asks users to immediately stop using all GRIGRI 2s with the first five digits of the serial number between 10326 and 11136. Excessive force on a fully extended handle may disable the braking function.”
– Petzl
05/19/11 // PETZL // Notice: ABSORBICA Request for IMMEDIATE INSPECTION (P/Ns: L57, L58, L58 MGO, L59, L59 MGO, L59 69, L70120 YG, L70150 IM, L70150 YM, L70150 I, L70150 Y, L70150 YM)
“Notice follows a May 5, 2011, accident involving a Petzl SCORPIO via ferrata lanyard. Because of the ABSORBICA’s similar tear-webbing shock absorption technology, Petzl has issued an inspection recall of both the SCORPIO and ABSORBICA.”
– Petzl
05/24/11 // PETZL // Recall: SCORPIO via Ferrata Lanyards (L60, L60 CK, L60 2, L60 2CK, L60 H, L60 WL, K29VF 1, K29VF 2, K29VE 1, K29VE 2, K29V 1, K29V 2) Manufactured Before May 17, 2011, Up to Serial Number 11137****
“Follows a via ferrata accident on Thursday the 5th of May 2011. Investigation and analysis of manufacturing procedures specific to the production of tear webbing energy absorbers has identified a weakness which could explain the defect leading to the cause of this accident.”
– Petzl
02/10/11 // PETZL // Information Regarding Counterfeit Products: CROLL (B16), ATTACHE (M35 SL), ASCENCION (B17) and RESCUE (P50)
“Illegal copies of the listed products were discovered in China. These counterfeit products show serious defects which affect their performance and strength.”
– Petzl
09/30/10 // PENSAFE // Recall Notice: 3730 Anchorage Connectors with the 07 B Year and Heat Code
“A heat treatment deficiency resulted in a potential embrittlement on anchorage connectors. This embrittlement may cause the threads on the stem to fracture prematurely from stress created by the torque of the nut during installation.”
– PenSafe
